You Can Diagnose & Fix 6 Toilet Problems

It’s not as hard as you might think to fix a toilet problem. You can use these six tips to help you. Toilet problems most often occur inside the tank. This is where all the mechanical parts are located. However, problems rarely occur outside of the tank.  Our sixth tip is for problems that occur outside of the tank. It’s located at the bottom, where the toilet attaches to the floor.

Understanding How Toilets Work

You’ll find a variety of tubes, balls, and levers when you lift the top of a toilet tank. Although it may look messy, the toilet tank works according to simple principles like gravity. The act of using the toilet handle activates a series of events that release water to the best toilet seat and then refill the tank. There are many toilet types today, but the most common one is the float ball. The handle triggers a trip lever, which lifts the flapper at the tank’s bottom. The water then flows through the hole into the toilet bowl.

Flushing triggers the refill process. The water level drops and the float ball opens an inlet valve. This allows water to be added to the tank via a refill tube. Water is then sent to the bowl via a second refill tube, which empties into an overflow tube. The float will rise with the water in the tank. The float stops water from flowing to the bowl and tank when it reaches 3/4″ below the top of the overflow.

Troubleshooting Toilets: 6 Problems and Solutions

To troubleshoot your specific issue, you can use the six common problems with toilet repair.

1. Water runs, But The Tank Won’t Fill Properly

To ensure that everything is in order, check the trip lever, handle, guide arm, football, and all their connections. Look out for the following problems:

  • Is the handle of the toilet (or any other component) too loose?
  • Is the guide arm or trip lever bent?
  • Is the trip lever’s connection to the guide arm strong enough for the float ball (about 3/4″ below the top) to rise sufficiently high?

2. Water Runs Continuously After The Tank is Filled

It is possible that the handle or trip assembly is not working correctly. To ensure it is properly seated, check the flapper. Check the seat (the part where the flapper rests) for corrosion to ensure that the flapper is properly seated. You will need to replace or clean the seat if it is corroded. The corrosion will prevent the flapper from sitting correctly. Make sure that the float is not contaminated with water.

3. Water Level is Too High or Low

The float ball may need to be adjusted downward. You should check that it isn’t damaged. It could also be full of water. Also, the inlet valve washers may be leaking and will need to be replaced. Make sure the flapper is properly seated. Finally, inspect the flapper’s seat for corrosion.

4. Toilet Won’t Flush Properly

To lower the water level, gently bend the float arm attached to the float ball downwards. If you prefer to raise it, bend it upwards. To adjust the float arm, you can use the adjustment screw located on top of your inlet valve. The water level in the tank should be at least 3/4″ below the top of the drain tube. If you want to get rid of a flushing problem so you should go for the best flushing toilet. It is the best option.

5. Tank Leaks at The Bottom

Adjust the fill tube that connects to the overflow tube. The washers at the inlet valve may need to be replaced. All nuts at the tank’s bottom should be tightened. If this fails, replace the washers.

6. BONUS: Toilet Leaks Where Seated

These are the most common issues you might find in your toilet tank. This is where your toilet’s bottom meets the floor, and it can be used to troubleshoot toilet problems.

Conclusion: Troubleshooting Toilets

It seems that the problem of toilets is enough to keep plumbers in the business. Our goal is to provide you with the information that you need to solve many of these issues yourself. First, you must know how to troubleshoot toilets and diagnose any problems that may arise.

For more information on how to solve these issues, click the links below. You will find step-by-step instructions. If those don’t work, you can always call a trusted plumber in your area.